Before you buy any products or jump straight into your cleaning your laminated floor, you should check with your manufacturer to get a better understanding of the material your floor is made from and what can and can’t be used or done to it. If you use a cleaner that is too strong, for example, you could damage your floor.Here are a few general tips to clean most laminate floors:
You will need:
Mop bucket
Sponge mop
Sweeping brush
Vacuum cleaner (with a specialized attachment)
Laminate floor cleaner
Hot water
What to do:
1.Sweep the laminate floors to remove all dirt and dust.
2. Vacuum the floor using the specialized attachment.
3. Read the instructions for using the laminate floor cleaner, you will most likely need to mix the cleaner with the hot water in a mop bucket. Mop the floor in the direction of the grain.
4.Rinse the mop as you wipe the various areas of the floor. Unless the laminate floor cleaner specifies that you should, there is no need to rinse the floor with water to remove traces of the floor cleaner.
Some stains, however, are stubborn, and cannot be removed by using this method alone. Here are some of the stains that you may come across and how to best deal with them:
Blood:using window cleaner and a damp cloth, wipe the stain, avoid putting too much liquids onto the laminate flooring in one go as this could damage it.
Alcohol stains: mix some warm water and detergent together and use this to rub the spot clean, if the stain is stubborn, try using denatured alcohol instead of the water and detergent.
Grease:get some ice, an ice pack or a pack of frozen vegetables will do, apply this to the stain until the grease has hardened. Scrape away the grease with a plastic spoon or knife and use window cleaner and a clean cloth to wipe the area completely clean.
Crayons: apply some spirits to a soft cloth and rub clean, alternatively apply toothpaste to the stain and wipe away with a cloth.
Nail Varnish: Check with your manufacturer to see what exactly you can use on your floor, varnish remover may be too strong therefore you may need some sort of scouring powder. Use a scouring pad to clean the area but avoid rubbing too hard as this may scratch the surface.
Ink:mix warm water and detergent and use this to remove the ink, if this doesn’t work you may need to hire an experienced cleaner.
Shoe marks: Use a pencil rubber to erase the marks.
Chewing gum:remove the chewing gum with a knife, taking care not to scratch the surface, and clean the floor with spirits. If the gum is difficult to remove, try freezing it first.
If you want to protect the environment, while also saving a little money, why not try to make your own floor cleaner, all you need to do is mix half a cup of white vinegar in with a gallon of water, this will clean away all dirt and leave a streak free finish to your floor. Alternatively, there are a number of environmentally friendly floor cleaners that you can buy from the supermarket, these may be slightly more expensive than normal cleaners, however, they can usually be used on more things cutting down on the variety of products you need to buy, furthermore, green clean products are stronger and therefore you don’t need to use as much.
Bio: Cindy Davis is writer and freelancer. She has great passion for cleaning and desinfection matters, as it is of great importance of her family’s health to always keep their home clean and sanitized. Here you may find some more related helpful information:http://www.londoncleaners.co.uk/end-of-tenancy-cleaning/
If it is a fresh stain then just remove the sucroe of moisture on the wood surface. The white ring is water vapor trapped on the surface of the finish. It can disappear sometimes because it is reabsorbed by dry air. Humidity can delay the process and using a hair dryer can accelerate the process. If your table has a satin or dull sheen, use a very soft steel wool pad and some lemon oil. Dip the pad in the oil and rub on the stained area in the direction of the grain of the wood. When the stain is removed you may have to polish the rest of the table to even out the sheen. As a final touch wipe off extra oil and apply a polish of your choice. For tables with glossy sheen use a little white toothpaste on a dry cotton towel and rub on stain. It the spot gets glossier than the rest of the area then use rubbing compounds to even the gloss. Use a polish of your choice once you finish. A simple trick is to apply Vaseline on the stain and wipe it off once it disappears. If none of the above work, then the water has penetrated deep inside and you will have to refinish. As far as a cleaner, you may be able to find one that cleans both, but you will not get the best results. Why? Because wood needs oil and conditioners to stay shiny and protected, and glass needs all grease and residue removed to be perfectly clear. Opposites will not work. My advice is to just stick with the good old Windex for the glass and Pledge for the wood. Clean the glass first so the overspray is wiped off with the polish. Spray the polish on the rag rather than directly on the furniture to prevent overspray back onto the glass. Once in a while, (monthly or so) reverse the process a bit. Use a good wood soap like Murphy’s oil soap to deep clean your wood and give it a good shine, then Windex the glass by spraying the rag. Yeah, it may be a bit more time consuming, but a good shine on a rich wood is worth it if done properly. Hope this helps!Blessings
Hello there, just became aware of your blog through Google, and found that it’s truly informative. I’ll be grateful if you continue this in future. A lot of people will be benefited from your writing. Cheers!
i have heard that ashes can clean water stains, but u may want to try holies.com and i believe that either windex or pledge puts out an all surface cleaner.
Nice post. I was checking constantly this weblog and I’m inspired! Very useful info particularly the remaining part 🙂 I deal with such info a lot. I was seeking this particular information for a very lengthy time. Thanks and good luck.
I together with my pals have already been looking at the excellent tips and hints located on your web page then instantly developed a terrible feeling I never thanked the website owner for them. Those men had been consequently very interested to see all of them and now have actually been loving these things. We appreciate you being very considerate and also for using varieties of essential subject matter most people are really wanting to discover. My personal sincere regret for not saying thanks to you sooner.
This posting was stored as a favorite :), I like your site!
If it is a fresh stain then just remove the sucroe of moisture on the wood surface. The white ring is water vapor trapped on the surface of the finish. It can disappear sometimes because it is reabsorbed by dry air. Humidity can delay the process and using a hair dryer can accelerate the process. If your table has a satin or dull sheen, use a very soft steel wool pad and some lemon oil. Dip the pad in the oil and rub on the stained area in the direction of the grain of the wood. When the stain is removed you may have to polish the rest of the table to even out the sheen. As a final touch wipe off extra oil and apply a polish of your choice. For tables with glossy sheen use a little white toothpaste on a dry cotton towel and rub on stain. It the spot gets glossier than the rest of the area then use rubbing compounds to even the gloss. Use a polish of your choice once you finish. A simple trick is to apply Vaseline on the stain and wipe it off once it disappears. If none of the above work, then the water has penetrated deep inside and you will have to refinish. As far as a cleaner, you may be able to find one that cleans both, but you will not get the best results. Why? Because wood needs oil and conditioners to stay shiny and protected, and glass needs all grease and residue removed to be perfectly clear. Opposites will not work. My advice is to just stick with the good old Windex for the glass and Pledge for the wood. Clean the glass first so the overspray is wiped off with the polish. Spray the polish on the rag rather than directly on the furniture to prevent overspray back onto the glass. Once in a while, (monthly or so) reverse the process a bit. Use a good wood soap like Murphy’s oil soap to deep clean your wood and give it a good shine, then Windex the glass by spraying the rag. Yeah, it may be a bit more time consuming, but a good shine on a rich wood is worth it if done properly. Hope this helps!Blessings
Hello there, just became aware of your blog through Google, and found that it’s truly informative. I’ll be grateful if you continue this in future. A lot of people will be benefited from your writing. Cheers!
i have heard that ashes can clean water stains, but u may want to try holies.com and i believe that either windex or pledge puts out an all surface cleaner.
Nice post. I was checking constantly this weblog and I’m inspired! Very useful info particularly the remaining part 🙂 I deal with such info a lot. I was seeking this particular information for a very lengthy time. Thanks and good luck.
I together with my pals have already been looking at the excellent tips and hints located on your web page then instantly developed a terrible feeling I never thanked the website owner for them. Those men had been consequently very interested to see all of them and now have actually been loving these things. We appreciate you being very considerate and also for using varieties of essential subject matter most people are really wanting to discover. My personal sincere regret for not saying thanks to you sooner.